How To Fix SD630 Lens Error
If your system has an sd630 lens bug, this guide can help.
Ask a new question
Use the free space below to post a new release of the Canon PowerShot SD630.
DownloadCheck out one of our Canon PowerShot SD630 manuals for freeCanon for PowerShot SD630
Points and prizes
See how it works
Create a free account
View detailed Canon customer service ratings, employee reviews and more directly on our partner site. Reminders
Canon update: failures February 2014 y.)
If you have received this information, please pass it on and share this article with others who may experience the same violations. Your help in the exchange will definitely be greatly appreciated, and karma will definitely prevail!
This is the most common type of digital security camera failure, lens sticking, lens sticking, also called bad lens. Some common error messages that can appear on the LCD screens of cameras with this key issue are “E18 lens error” (old Canon Powershot), “ACCESS” error (Sony Cybershot), “Zoom error” (Fuji Finepix), “Lens closed.” (Kodak Easyshare), “Lens Error, Machine Camera”, or simply “Lens Error” (Nikon Coolpix and some other camera makers have recently started using this option). Some devices may not display anything at all, just beep when the lens is turned off, then the camera turns off. Sometimes the lens doesn’t even move.
Tips are listed in order of risk of damage to the camera. So be sure to tryrun them in the given order. And remember that these fixes (particularly #6 and #7) should only be seriously considered for an out-of-warranty device that will be overpriced to repair, and otherwise just be considered a bug if it’s not fixed :
Solution #1: Power off the camera and wait a few minutes. Install new batteries (preferably rechargeable NiMH 2500 mAh or higher) and turn on the camera. If you are using rechargeable batteries and they have expired, you should consider purchasing new rechargeable electronics as they may not have enough energy to run the device.
How can I fix my camera lens error?
If the lens is partially or fully extended, try gently pulling or squeezing the barrel of the lens gun while the camera attempts to extend or retract it. Usually, when the lens is fed, the main section rotates and you can try to gently “help” it.
Fix #1a: New. If the battery is not working, try holding the menu, function, function settings, or possibly the OK button while turning on the electronic camera. This, along with fixes #1c and #2, sometimes causes lens bugs that occur when batteries run low while the lens has been extended.
Fix #1c. For those of you who are still able to connect the camera to the menu, try to find and select the options.Factory data reset to restore the camera to its original factory state. On some Canon cameras, this now requires holding down the alternative menu while the camera is on to get up to 10 seconds. However, note that sometimes an objective error can override the reset setting, so this setting may not be respected.
How do I fix my Canon lens error?
So, if the lens mounts are fine and you get a fantastic error message… turn off the camera… and put the lens in manual mode… turn off autofocus… then turn the camera back on the photo and see if you can do good shot with manual focus lens. Again, if this is true, then there is a brake, or look for profit, spin for free, stop!
Fix #2: If the camera batteries are completely dead while the lens is still open, the camera may display a lens error or not start properly when new batteries are added. Remove the memory card and leave this item removed, then insert clean batteries. Turning on an electronic camera with the card removed can bring this situation back to life, unlike many cameras that cause a reset. Error E30 (for old Canons) means that you have not installed a good memory card, so turn it off, connect the SD card account and turn it on again.
Solution #3: Connect the audio/video (AV) cable from the camera and turn on the camera. Connecting this cable ensures that the camera’s LCD screen is notwill work during startup. This means that a lot of extra power is available for the entire camera lens motor during the loading process. This extra power can be useful for getting through gravel or sand particles, which can unfortunately clog the lens. If an AV cable doesn’t fix most lens bugs on its own, consider this cable as the go-to cable if you’re suffering from acne trying to provide 4, 5, 7 and as an important way to provide extra performance to support those fixes. . However, please note that I do NOT recommend leaving the cable plugged in during Fix 6 as you may damage the AV aperture by pressing on the camera. Do not connect the main cable until you have touched most of the camera.
Fix Spot #4: The camera is back to the table, facing the ceiling. While holding down the shutter button, press the spotlight on button at the same time. The idea is that cameras try to achieve autofocus by extending the lens, perhaps with the guide pins of the lens barrel in their grooves.
Why does my camera says lens error?
Aiming errors should be fairly frequent. It is usually sand, possibly sand, that interferes with the lens file expansion mechanism. Or the camera has been dropped with the lens extended. Or the whole camera was on, only the lens was locked to protect its extension.